Post Mitigation Diagnostics

WPB Home Page

Fan Performance & Wattage
Choosing best Fan to use
Reducing System Noise
Pipe & Fitting Pressure Drop
PFE Testing
Measuring Airflow
Radon in Concrete
All Info pages

Accurately measuring Airflow in piping is never trivial!! This page will review some of the ways it is done. But first let me describe the easiest way to use a pitot tube to make this measurement in common radon piping. This requires a magnehelic or digital micro-manometer and of course a pitot tube.

Airflow in a pipe is not uniform. When air enters a turn (elbow) airflow is most disrupted coming out of the turn. The general rule is make airflow measurements at least 2 pipe diameters before an elbow and at least 8-10 pipe diameters after an elbow. To most accurately measure airflow in a pipe that has no airflow vanes to make the airflow more uniform you would average multiple pitot measurements using the following pattern. Not trivial as you can see.

In my lab I have carefully calibrated a flow grid using a lo-flow balometer to determine the actual airflow. I then made pitot tube measurements in the center of the pipe and obtained the following calibration figures for different common radon piping sizes.

Center Pipe - Pitot Tube - Calibration Factors

Drill a small hole in the side of the pipe in a location that will have the straightest airflow.  Connect the side port of the pitot tube into the reference port of the digital micro-manometer or the magnehelic.  Connect the bottom port of the pitot tube to the Inlet port of the digital micro-manometer or magnehelic.   Be sure to aim the pitot tube directly into the air stream right in the middle of the pipe.  I often wrap a small strip of duct tape around the pitot tube at the half pipe size distance on the pitot so I can more easily place it half way into the pipe. Set your Digital Micro-manometer to read in inches of water column.  This is the velocity pressure.  If it reads in Pascals take that measurement and divide by 249 to get the velocity pressure in inches of water.

Enter the velocity pressure into a calculator and press the square root function.  Multiple this result times the calibration factor listed for the pipe size you are measuring from the table above.  This is the approximate CFM flowing through your pipe.

Radon Job Photos          Fan Performance          All Info Pages         WPB Home

Accurately measuring Airflow in piping is never trivial!! This page will review some of the ways it is done. But first let me describe the easiest way to use a pitot tube to make this measurement in common radon piping. This requires a magnehelic or digital micro-manometer and of course a pitot tube.

Airflow in a pipe is not uniform. When air enters a turn (elbow) airflow is most disrupted coming out of the turn. The general rule is make airflow measurements at least 2 pipe diameters before an elbow and at least 8-10 pipe diameters after an elbow. To most accurately measure airflow in a pipe that has no airflow vanes to make the airflow more uniform you would average multiple pitot measurements using the following pattern. Not trivial as you can see.

In my lab I have carefully calibrated a flow grid using a lo-flow balometer to determine the actual airflow. I then made pitot tube measurements in the center of the pipe and obtained the following calibration figures for different common radon piping sizes.

Center Pipe - Pitot Tube - Calibration Factors

Drill a small hole in the side of the pipe in a location that will have the straightest airflow.  Connect the side port of the pitot tube into the reference port of the digital micro-manometer or the magnehelic.  Connect the bottom port of the pitot tube to the Inlet port of the digital micro-manometer or magnehelic.   Be sure to aim the pitot tube directly into the air stream right in the middle of the pipe.  I often wrap a small strip of duct tape around the pitot tube at the half pipe size distance on the pitot so I can more easily place it half way into the pipe. Set your Digital Micro-manometer to read in inches of water column.  This is the velocity pressure.  If it reads in Pascals take that measurement and divide by 249 to get the velocity pressure in inches of water.

Enter the velocity pressure into a calculator and press the square root function.  Multiple this result times the calibration factor listed for the pipe size you are measuring from the table above.  This is the approximate CFM flowing through your pipe.

All Info Pages            WPB Home

Radon Job Photos          Fan Performance

 PFE/Communication Testing         Pipe & Fitting Pressure Drop

Radon mitigation call Integra Environmental 610 346-8004
For consulting Bill 484 626-0993 - © 2021 Bill Brodhead

For Radon System estimates or Fan repairs call
Integra Environmental at 610- 346-8004
© 2021 Bill Brodhead

For consulting call Bill at 484 626-0993